Send your capacity (kg/h) and your frozen block size. We reply with a model recommendation and a quote within 24 hours.
Industrial Meat Grinders: Choose by Capacity and Frozen Block Size
We build industrial meat grinders in our own plant in Zhucheng, Shandong — not through a trading layer. The JR series covers 500 kg/h to 16,000 kg/h (1,102–35,274 lbs/h) across eight models, and grinds frozen blocks from 1 kg to 50 kg directly at -18 °C without pre-thawing. The body, frame and guards are all SUS304 — not a stainless cover over a painted frame.
The table below lists all eight models by capacity, maximum frozen block, auger diameter, motor power and container load. Shortlist two or three, then send us your daily output and block size — we return a model recommendation, a line layout and a quote within 24 hours.
Jump to the full capacity table ↓
Contents
- 1. 1. What “industrial” actually means here
- 2. 2. The four numbers that decide your model
- 3. 3. Capacity table: 0.5 to 16 t/h
- 4. 4. Frozen block vs fresh meat
- 5. 5. Why the whole machine is 304, not just the parts that touch meat
- 6. 6. Grinder alone, or mixing-grinding combined?
- 7. 7. What drives the price
- 8. 8. Which model for which product
- 9. 9. Our factory
- 10. 10. Frequently asked questions
- 11. Get a quote within 24 hours
1. What “industrial” actually means here
A commercial grinder and an industrial grinder are separated by four operating realities, not by the phrase “heavy-duty” on a spec sheet.
- Continuous runtime. Industrial units run 16–24 hours per shift; countertop commercial units are intermittent. JR-200 and above use high-torque reducers and multi-layer overload protection for continuous duty.
- Frozen input. A true industrial meat grinder accepts whole frozen blocks at -18 °C. The auger crushes and discharges in one pass — no band saw pre-cutting, no tempering room.
- Hygiene access. Grinding head, auger, hopper and hole plate come apart without tools for washdown. IP65 control box is standard on the JR series.
- Throughput rated per hour. If a supplier quotes kg/min without a rated hourly figure, that number is a peak, not a production rate. Every model on this page is rated in kg/h and lbs/h simultaneously, with the input condition stated.
2. The four numbers that decide your model
Number 1 — Capacity (kg/h). Start from your daily output: daily output ÷ effective hours ÷ 0.8. The 0.8 accounts for a 25% headroom over frozen-block hardness, knife wear and changeover. Running one 8-hour shift at 4 t/day gives 4,000 ÷ 8 ÷ 0.8 = 625 kg/h, which points at JR-120 (1,000 kg/h). Running two shifts, JR-100 at 500 kg/h may already be enough.
Number 2 — Maximum frozen block (kg). This decides hopper opening and auger geometry. JR-100/120/130/160 handle blocks up to 1–15 kg; JR-200/250 up to 20–25 kg; JR-300 up to 30 kg; JR-300B is the only model rated for 50 kg whole frozen pans. Do not pick a model whose maximum block weight is below your carton size — the auger will stall even when the motor is large enough.
Number 3 — Discharge particle size (mm). Hole plates are selectable from 4 mm to 88 mm depending on model. Use 4–8 mm for fine emulsions and pet raw food, 10–20 mm for sausage and patties, 30–88 mm for coarse pre-grinding ahead of a bowl cutter.
Number 4 — Floor space and power. JR-300B measures 2,700 × 1,200 × 2,000 mm and draws 93 kW. Confirm your available supply before shortlisting: 220 V / 380 V / 440 V, 3-phase, 50 or 60 Hz are available. A model that fits your capacity but not your transformer is not a candidate.
3. Capacity table: 0.5 to 16 t/h
| Model | Typical input | Capacity kg/h (lbs/h) | Max frozen block kg | Auger dia. mm | Motor kW (HP) | Dimensions L×W×H mm | Weight kg (lbs) | Load 20GP / 40HQ |
|---|---|---|---|---|---|---|---|---|
| JR-100 | Fresh · frozen ≤ 1 kg | 500 (1,102) | 1 | 100 | 4.0 (5.4) | 900 × 550 × 1,000 | 175 (386) | 33 / 76 |
| JR-120 | Fresh · frozen ≤ 2.5 kg | 1,000 (2,205) | 2.5 | 120 | 7.5 (10.1) | 1,050 × 600 × 1,050 | 198 (437) | 25 / 59 |
| JR-130 | Fresh · frozen ≤ 10 kg | 2,000 (4,409) | 10 | 130 | 15 (20.1) | 1,450 × 700 × 1,050 | 465 (1,025) | 16 / 38 |
| JR-160 | Fresh · frozen ≤ 15 kg | 3,000 (6,614) | 15 | 160 | 18 (24.1) | 1,500 × 800 × 1,200 | 520 (1,146) | 13 / 29 |
| JR-200 | Frozen blocks · also fresh | 2,000–4,000 (4,409–8,818) | 20 | 200 | 30 (40.2) | 1,600 × 900 × 1,440 | 720 (1,587) | 9 / 21 |
| JR-250 | Frozen blocks · also fresh | 4,000–8,000 (8,818–17,637) | 25 | 250 | 45 (60.3) | 2,200 × 1,000 × 1,600 | 1,600 (3,527) | 5 / 13 |
| JR-300 | Frozen blocks | 8,000–10,000 (17,637–22,046) | 30 | 300 | 75 (100.6) | 2,350 × 1,000 × 1,600 | 2,500 (5,512) | 5 / 9 |
| JR-300B | Whole frozen pans | 12,000–16,000 (26,455–35,274) | 50 | 300 | 93 (124.7) | 2,700 × 1,200 × 2,000 | 3,600 (7,937) | 40HQ only: 6 |
How to read the capacity column. For JR-100 to JR-160, the figure is the rated output on fresh or tempered meat; they also accept frozen blocks up to the weight shown. For JR-200 to JR-300B, the range is the rated output on frozen blocks at -18 °C, where throughput depends on block temperature and hardness. This is why JR-160 shows a single figure of 3,000 while JR-200 starts at 2,000 — the two numbers are measured on different inputs.
All models: full SUS304 — hopper, auger, grinding head, hole plate, knife, body panels, frame and guards · one set of hole plates included per order · plate range confirmed per model: 4–22 mm on most, up to 88 mm on the JR-300.
Container load is per model in a crated wooden case: the crate adds 100 mm to length and width and 300 mm to height (150 mm fork pocket, 50–70 mm bottom board, 10 mm top board), plus about 15% to net weight, checked against the container door opening. Figures assume a 20GP of 33.1 m³ and a 40HQ of 76 m³ at 85% utilisation. The JR-300B measures 2,300 mm once crated, which exceeds the 20GP door height of 2,280 mm, so it ships in a 40HQ only. For US inland delivery, federal road weight limits reduce a 40HQ to roughly 20 t of cargo — ask us for the inland load before you calculate freight.
How to convert your daily output into kg/h
Formula: daily output (kg) ÷ effective working hours ÷ 0.8 = required kg/h. The 0.8 factor adds 25% headroom for frozen-block hardness, knife wear and changeover.
Example 1 — 2,000 kg/day on one 8-hour shift: 2,000 ÷ 8 ÷ 0.8 = 312 kg/h → JR-100 (500 kg/h) is the smallest safe model.
Example 2 — 10,000 kg/day on two shifts: 10,000 ÷ 16 ÷ 0.8 = 781 kg/h → JR-120 (1,000 kg/h).
If your output is already in tonnes, multiply by 1,000 before applying the formula.
4. Frozen block vs fresh meat
The same grinder can run both, but the feeding method and the auger load are different.
Frozen blocks at -18 °C. JR-200/250 and JR-300/300B use a low-compression, high-torque auger that bites into the block and discharges without smearing fat. The block limits are real: JR-200/250 up to 20–25 kg, JR-300 up to 30 kg, JR-300B up to 50 kg. Within those limits, no band saw pre-cutting is required.
Fresh and tempered meat. JR-100/120/130/160 handle fresh meat, fruit, vegetables and composite materials with the same integrated auger. When switching from frozen to fresh, reduce the feed rate — fresh meat needs less torque but more even hopper loading to avoid bridging.
If 80% of your input is frozen blocks, size by the frozen-block column first and confirm capacity second.
5. Why the whole machine is 304, not just the parts that touch meat
The usual compromise. Most suppliers build the contact parts — hopper, auger, head, plate, knife — in 304, and the frame, body panels and guards in 201 or painted steel. It is a legitimate cost decision, and it is the main reason a competitor's quote comes in below ours on the same capacity.
What 201 does in a washdown room. 201 carries less nickel and no molybdenum. Hose it down daily with chlorinated water and it starts to pit — first at the welds, then at the floor-level seams. The rust stains end up on the floor, on the operator's boots, and eventually on product that has nothing to do with the machine. No buyer asks for that in writing, and every buyer notices it on the audit walk.
What you can weigh instead of argue. A 1.1 kW grinder built this way weighs about 70 kg. An aluminium countertop unit of the same power weighs around 37 kg. The gap is steel, not marketing — the weight figures in the table above are the honest version of the claim.
Where 201 can still appear. Only on request. A custom build, or an added support frame for an oversized hopper or an extended discharge, may be fabricated in 201 to hold the price. When that happens we say so on the quotation and note it in the drawing — we do not slip it in and hope you do not look.
What to ask any supplier. Ask two questions: is the frame 304 or 201, and can you send the material certificate for the contact parts and the frame. A supplier who produces the first certificate but not the second has already answered.
6. Grinder alone, or mixing-grinding combined?
A standalone grinder is the right choice when your downstream step already has a mixer, or when you change products often and want one compact machine to clean. On the JR series the head, auger, hopper and plate come apart without tools for washdown.
A mixing-grinding combined machine makes sense when you add brine, binders or fat directly at the grinding stage, and when floor space is tight. The trade-off is cleaning complexity — the mixing paddle adds surfaces.
If you are building a sausage or patty line, compare both before locking the layout. See our Mixer Grinder (Mixing and Mincing Integrated Machine) for the combined option.
7. What drives the price
We do not publish a single “from” price, because the same JR-200 frame can be configured three ways. Price moves with four variables:
- Motor brand and efficiency class. A 30 kW motor from a tier-1 brand and from a budget brand differ in price and in continuous-duty thermal margin.
- Auger diameter and machining. An auger that accepts 25 kg frozen blocks needs more steel and more machining time than a 10 kg auger.
- Contact-material certification. SUS304 contact parts with mill certificates cost more than uncertified “304”.
- Voltage and control. 440 V / 60 Hz for the US, IP65 control box and PLC options all change the bill of materials.
Send your capacity and block size; the quote we return itemises these four variables so you can compare configurations line by line.
8. Which model for which product
Pet raw food. JR-100/120 for 500–1,000 kg/h pilot lines; JR-200/250 for 2,000–4,000 kg/h commercial raw pet food.
Sausage and emulsified products. JR-120 or JR-130 ahead of a bowl cutter, with a 4–8 mm plate.
Burger patties and coarse ground. JR-200 at 2,000 kg/h rated, 10–20 mm plate.
Frozen block pre-grinding ahead of bone separation. JR-300B, because 50 kg whole pans go in without pre-cutting.
If your product is not listed, send a 100-word process description and we will map it to a model — not the other way round.
9. Our factory
The JR series is manufactured by Zhucheng Reno Machinery Co., Ltd., established in 2004, in a 5,000 m² plant in Zhucheng, Shandong. We export to 17 markets. CE certificate HDBT-2021062301S is held for the JR series — we send the certificate copy with the quotation so you can check which models it lists, and the number can be verified with the issuing body, HDBT TEST.
We are a factory, not a trading company — the person who quotes your line is looking at the same production floor.
10. Frequently asked questions
What is the difference between a commercial and an industrial meat grinder?
An industrial meat grinder is rated for continuous 16–24 hour operation and accepts whole frozen blocks. A commercial grinder is intermittent-duty and normally needs tempered or fresh meat.
Can it grind frozen meat blocks directly, and up to what temperature?
Yes. Every JR model processes frozen meat at -18 °C without pre-thawing. The block limit depends on the model: JR-100/120/130/160 up to 1–15 kg, JR-200/250 up to 20–25 kg, JR-300 up to 30 kg, JR-300B up to 50 kg.
What capacity do I need to produce 2 tonnes per day?
On one 8-hour shift: 2,000 ÷ 8 ÷ 0.8 = 312 kg/h, so JR-100 at 500 kg/h is the smallest safe model. On two shifts the same machine runs with more headroom. Confirm your actual shift pattern before choosing.
What is the price range for an industrial meat grinder?
Price depends on capacity, frozen block size, motor brand and voltage. We do not publish a single range because the same frame can be configured several ways. Send your capacity and block size, and the quote will itemise motor, auger, material and control.
What is the lead time and minimum order quantity?
Standard lead time is 45 days; customised configurations run about 60 days. MOQ is one unit for standalone grinders and one line for turnkey projects.
Which voltage is available for the US, EU and Middle East?
220 V / 380 V / 440 V, 3-phase, 50 or 60 Hz. For North America, confirm 440 V / 60 Hz at the time of order. 208 V and 480 V are not listed as standard on this page — they require a separate confirmation with our electrical engineer, and we would rather tell you that up front than after the order.
Which spare parts should I stock, and how fast can you ship them?
Stock one set of hole plates and knives for your most-used particle size, plus the auger seal kit. Small emergency parts can ship by air; standard spares follow the 45-day production slot unless they are already in stock.
Can you integrate the grinder into our existing production line?
Yes. We size the grinder against the slowest upstream and downstream step, and supply the transition chute and control interface. Send a simple line sketch with hourly rates before and after the grinder, and we return a layout within 24 hours.
Get a quote within 24 hours
Send your capacity (kg/h) and frozen block size. We reply with a model recommendation and a quote within 24 hours.
Prefer to talk directly?
WhatsApp: +86 152 6468 7073 |
Email: sales@longerfm.com
